French Doors Cost UK 2026: Prices, Fitting and Conversions

White French doors opening from a garden room onto plants

Quick answer (November 2026): French doors cost about £950–£1,250 fitted for a standard uPVC pair in an existing opening, £1,300–£1,500 for aluminium and £1,250–£2,400 for timber or oak-effect sets. Turning a window into French doors usually costs £1,700–£2,650, and cutting a brand-new opening costs £3,100–£3,400 or more, because of the lintel, building control and making good. Supply-only uPVC sets start at roughly £680–£960 depending on width. Prices compared from MyJobQuote (Oct 2026), Trade2Base (Jun 2026), PriceYourJob (2025) and supplier lists.

French doors cost less than most people expect when you are swapping a tired pair like for like, and a lot more when you are making a new opening. The door itself is often the smaller part of the bill. This guide sets out the French doors cost for each kind of job in 2026, what drives the price, the rules on planning and Building Regulations, and three worked examples you can compare against your own quotes.

White French doors opening from a garden room onto plants
White glazed French doors opening onto a garden. Photo: Unsplash (Marcel Heil)

Extension Costs is an independent cost guide, not a door company. Our figures come from the published price guides and supplier lists named in each table, so you can check them.

French doors cost at a glance (2026)

JobTypical fitted costMain source
Replace uPVC French doors, same opening£950–£1,250MyJobQuote, Oct 2026
Replace uPVC French doors incl. removal and making good£1,200–£2,000Trade2Base, Jun 2026
Replace any French doors in the same opening (all materials)£1,750–£2,250MyJobQuote, Oct 2026
Turn a window into uPVC French doors£1,700–£2,650Checkatrade; MyJobQuote
Cut a new opening and fit French doors£3,100–£3,400+MyJobQuote; Checkatrade
Fit only (you supply the doors)£300–£600Trade2Base, Jun 2026

The spread is wide because “French doors” covers anything from a £700 stock uPVC pair dropped into an existing frame to a made-to-measure aluminium set in a widened wall. The rest of this guide breaks those numbers down.

Pair of glazed timber French doors looking out onto an autumn garden
Timber French doors cost more than uPVC but suit older houses. Photo: Unsplash (Magnus Jonasson)

French doors prices by material

Material is the biggest single factor once the opening is sorted. MyJobQuote’s October 2026 guide splits each price into labour and supply:

MaterialSupplyLabourTotal fitted
uPVC£700–£900£250–£350£950–£1,250
Aluminium£1,000–£1,100£300–£400£1,300–£1,500
Softwood timber£1,000–£1,400£250–£350£1,250–£1,750
Solid oak laminate£1,700–£1,900£400–£500£2,100–£2,400

Source: MyJobQuote French door installation cost, updated 6 October 2026.

Trade2Base’s June 2026 pricing guide for installers puts all three materials higher, because its figures include removal of the old unit and making good:

  • uPVC: £1,200–£2,000 supplied and fitted, like for like.
  • Aluminium: £1,800–£3,500+, with “no real upper ceiling” on bespoke work.
  • Timber: £2,000–£4,000+, engineered softwood at the lower end and hardwood such as oak at the top.

Source: Trade2Base, French door installation costs UK, 14 June 2026.

Composite French doors sit between uPVC and timber. PriceYourJob lists them at £1,100–£1,600 fitted for a 1,200mm set, against £500–£800 for uPVC of the same width (PriceYourJob, updated July 2025). That guide is older than the others, so treat it as a guide to the gap between materials rather than a current price.

White painted French doors with Georgian-style glazing bars between shutters
Glazing bars and coloured finishes add to the price. Photo: Unsplash (Roger Bradshaw)

French doors cost by size

Most UK French door sets come in three standard widths at 2,100mm high. Wider sets cost more, but not by much, because fitting time barely changes.

Width x heightSupplyLabourTotal fitted
1,200 x 2,100mm£700–£1,300£300–£400£1,000–£1,700
1,500 x 2,100mm£750–£1,350£350–£450£1,100–£1,800
1,800 x 2,100mm£800–£1,400£400–£500£1,200–£1,900

Source: MyJobQuote, October 2026 (all materials).

If you are pricing supply-only, one online supplier’s list (DoorsDirect2U, prices “as of late 2025”, VAT included, free mainland delivery) gives a useful benchmark:

WidthWhite uPVC (supply only)Aluminium (supply only)
1,200mm£683£1,278
1,500mm£739£1,419
1,800mm£879–£957£1,549

Source: DoorsDirect2U. Retail list prices change often, so check the current figure before you order.

Made-to-measure sizes, coloured foils (anthracite grey, black, woodgrain) and dual colours all add to the price. Trade2Base says these raise the uPVC figure above its £1,200–£2,000 range but doesn’t give a number. Ask for the white-on-white price and the coloured price side by side so you can see the uplift.

Labour costs and how long fitting takes

A like-for-like swap is usually a one-day job for two fitters. MyJobQuote says fitting takes 2–8 hours, with total labour of £300–£700 for up to two people, and up to about £900 when an extra labourer is needed for heavy lifting or structural work.

Day rates in PriceYourJob’s 2025 guide are £150–£200 for a fitter and £80–£100 for a labourer, so roughly £250–£300 a day for a two-person team. Checkatrade’s older guide uses £175 a day for an installer and £100 for a labourer.

Fit-only jobs, where you buy the doors and an installer fits them, run at £300–£600 for a straightforward swap (Trade2Base). Not every installer will fit doors they didn’t supply, and some won’t guarantee the frame. Ask before you buy.

Window conversions and new openings take longer: usually 1–2 days for a window conversion and 2–3 days or more for a new opening, plus time for the plaster to dry before decorating.

Extras that change the price

ExtraTypical costSource
Side panels / sidelights£200–£500 per panelTrade2Base, Jun 2026
Integral blinds£150–£350 per leafTrade2Base, Jun 2026
Triple glazing upgrade£150–£400Trade2Base, Jun 2026
Removal and disposal of old doors£50–£150DoorsDirect2U
Skip hire (window conversions, brick rubble)about £220MyJobQuote, Oct 2026
Steps or decking outside a raised opening£1,000–£5,000Checkatrade, 2022

Two extras catch people out. The first is steps: if the new doors sit above garden level you’ll need a step, a landing or decking, and Checkatrade’s range for that is wide. The second is making good inside: plastering the reveals, a new floor threshold and redecorating. Make sure the quote says whether that’s included.

Turning a window into French doors

This is the most common French door job after a straight replacement. The builder removes the window and the brickwork below the sill, trims the opening to the door height and fits the new set. If the opening stays the same width, the existing lintel can often stay.

Published prices for the whole job:

  • MyJobQuote (Oct 2026): around £2,350–£2,650 for uPVC French doors.
  • Checkatrade: about £1,700 in total, split £600 labour and £1,100 materials including council fees. That guide was last updated in 2022, so allow for inflation.
  • Trade answers on MyJobQuote’s forum for a 2,100 x 2,100mm lounge window conversion ranged from £1,150 (including plaster) to around £3,500 all in. Most sat between £1,600 and £3,000.

Expect the top of the range if the opening needs widening (a new, longer lintel), the wall is solid brick or stone, there are radiators or sockets to move, or the floor inside needs a new threshold.

Do you need a new lintel?

Not always. If the door is the same width as the old window, the lintel above usually carries on doing its job. If the opening gets wider, the existing lintel won’t span it and a new one is needed. A structural engineer should size it (see structural engineer cost), and building control will need to approve it.

Trade2Base prices the structural side of a new or widened opening, covering engineer, lintel, propping, building control and making good, at £1,000–£2,500+ on top of the doors. A wide opening in a load-bearing wall may need a steel beam instead of a lintel; our steel beam cost guide and load-bearing wall removal cost guide cover those jobs.

Creating a new opening for French doors

Cutting a fresh opening in an external wall is the most expensive way to get French doors. MyJobQuote puts it at roughly £3,100–£3,400, and Checkatrade at about £3,125, for uPVC doors. Aluminium or timber doors, a wider opening or a London postcode push it higher.

The work usually involves:

  1. A structural engineer’s calculation for the lintel or beam.
  2. A building control application, because the work changes the structure.
  3. Temporary propping while the brickwork is cut out.
  4. Fitting the lintel, cavity tray and closers, then the door frame.
  5. Making good inside and out: plaster, render or brick slips, threshold and decoration.

If you are planning a kitchen or rear extension at the same time, it’s usually cheaper to build the opening into the extension than to cut one now and alter it later. See our kitchen extension cost and rear extension cost guides.

Planning permission and Building Regulations

Do French doors need planning permission?

Usually not, for a house. Swapping doors, or turning a rear window into doors, normally falls under permitted development as long as the materials look similar to the rest of the house. You are more likely to need permission if:

  • the house is listed (listed building consent is needed for almost any change);
  • it’s in a conservation area or covered by an Article 4 direction removing permitted development rights;
  • it’s a flat or maisonette, which have no householder permitted development rights; or
  • the new opening is on a front elevation facing a road, or an upper-floor side wall.

If you do need a householder application, the fee in England is £548 until 7 December 2026 and £575 from 8 December 2026 under SI 2026/1192 (legislation.gov.uk). A lawful development certificate costs half the householder fee. Our planning permission cost guide has the full fee list.

Do French doors need Building Regulations approval?

Yes, but usually through your installer. The Planning Portal says replacing an external door that is 50% glazed or more requires Building Regulations approval, and so does creating a new opening (Planning Portal: windows and doors, Building Regulations). If your installer is registered with a competent person scheme, such as FENSA or CERTASS, you don’t need to make an application for a replacement: they self-certify it. You should get a certificate within weeks of the job; keep it, because your buyer’s solicitor will ask for it.

A new or widened opening is different. It needs building control approval for the structural work, because self-certification schemes don’t cover lintels and new openings. Building control charges vary by council. As one example, the Royal Borough of Windsor and Maidenhead’s 2026/27 charges include £345 for a building notice for a single beam or lintel and £495 for small structural alterations under £5,000 (incl. VAT). Your council’s figure may be higher or lower; our building regulations cost guide compares several councils.

The main technical rules a compliant set must meet:

  • Energy (Approved Document L): a replacement door that is more than 60% glazed is held to the window standard of 1.4 W/m²K or better (or an equivalent energy rating band), according to industry summaries of Table 4.2. Most new double-glazed sets meet this; ask for the figure on the quote.
  • Safety glazing (Approved Document K): glass in doors at low level must be toughened or laminated so it breaks safely. Every reputable door set uses safety glass as standard.
  • Security (PAS 24): required for new dwellings under Part Q, and a good standard to ask for on any replacement. Look for multi-point locking.

Worked examples

These examples use the published prices above. They are planning guides, not quotes. Your installer’s figure will depend on the wall, access and the doors you choose.

Example 1: Like-for-like uPVC swap, 1,500mm, Midlands semi

ItemLowHigh
White uPVC French doors, 1,500mm (supply)£739£900
Fitting, two-person team (fit-only rate)£300£600
Removal and disposal of old doors£50£150
Total£1,089£1,650

Most firms quote this job supplied and fitted at £950–£2,000 (MyJobQuote and Trade2Base). Buying the doors yourself saves little and can complicate the guarantee.

Example 2: Lounge window to uPVC French doors, same width (1,500mm)

ItemLowHigh
uPVC French doors, 1,500mm (supply)£740£900
Two-person team, 2 days (£250–£300 a day)£500£600
Cut out brickwork below sill, make good inside and out*£300£600
Skip for rubble£220£220
Building control (only if the lintel needs changing)£0£345
Total£1,760£2,665

*Our allowance, not a published figure. It covers plaster to the reveals, a threshold and external brick or render repairs.

That lands inside MyJobQuote’s £2,350–£2,650 range at the top and close to Checkatrade’s £1,700 at the bottom.

Example 3: New 1,800mm opening with aluminium French doors, London

ItemLowHigh
Aluminium French doors, 1,800mm (supply)£1,549£1,549
Fitting labour (1,800mm set)£400£500
Structural work: engineer, lintel, propping, building control, making good£1,000£2,500
London uplift on labour and structural work (+20–30%)£280£900
Total£3,229£5,449

The London uplift is an estimate: one 2026 builder’s guide puts London prices 20–30% above the national average for door work. If the wall is load-bearing and the opening is wide, a steel beam may replace the lintel and the structural line can rise further.

French doors vs patio doors vs bifolds

French doors are usually the cheapest of the three for a standard opening, and they open fully without a track at floor level. Sliding patio doors cost about the same for uPVC but save space inside. Bifolds open the widest but cost two to four times as much.

Door typeTypical fitted price (uPVC unless stated)Best for
French doors£950–£1,250Openings up to about 1.8m; classic look
Sliding patio doorsfrom about £850Small rooms where doors can’t swing in
Bifold doors£1,950–£4,700 (3-panel)Wide openings onto a garden

See our patio doors cost and bifold doors cost guides for full price breakdowns.

How to keep the cost down

  • Keep the opening the same width. No new lintel means no engineer and, usually, no building control fee.
  • Stick to standard sizes. 1,200, 1,500 and 1,800mm sets are cheaper than made-to-measure.
  • Choose white uPVC unless you want a colour enough to pay for it. Ask for both prices.
  • Bundle the work. If windows are being replaced too, one installer and one visit costs less.
  • Get a FENSA or CERTASS installer for replacements, so you don’t pay building control fees.
  • Get itemised quotes that show doors, fitting, structural work, making good and disposal separately.

Ready to price it up? Get a free quote: we’ll pass your details to one vetted local builder who can quote for the opening and the doors together.

Frequently asked questions

What is the average cost of having French doors installed?

About £950–£1,250 for a standard uPVC pair in an existing opening, and £1,300–£2,400 for aluminium or timber. MyJobQuote’s October 2026 guide gives a £2,000 overall average across all materials and jobs.

Can I change a window to French doors?

Yes. It’s a common job and usually doesn’t need planning permission for a house. Expect £1,700–£2,650 for uPVC doors if the opening stays the same width. Widening it needs a new lintel and building control approval, adding £1,000–£2,500 or more.

Do French doors need planning permission?

Not usually for a house, if they look similar to the existing doors and windows. Listed buildings, flats, conservation areas with Article 4 directions and new front-facing openings may need consent.

Do I need Building Regulations approval for French doors?

Replacement doors must meet the Building Regulations, but a FENSA or CERTASS registered installer can self-certify them. A new or widened opening needs building control approval for the structural work.

Which is cheaper, composite or uPVC French doors?

uPVC is cheaper. PriceYourJob’s 2025 guide lists a 1,200mm uPVC set at £500–£800 fitted and a composite set of the same size at £1,100–£1,600.

How long does it take to fit French doors?

A like-for-like swap usually takes 2–8 hours. Converting a window takes 1–2 days, and a new opening 2–3 days or more, plus drying time before decorating.

What’s the difference between French doors and double doors?

French doors are a pair of mostly glazed doors that open from the middle with no fixed post between them. “Double doors” is a broader term for any pair of doors, glazed or solid, internal or external.

Are French doors cheaper than bifold doors?

Yes, usually by a wide margin. A uPVC French door set costs about £950–£1,250 fitted, against roughly £1,950–£4,700 for a three-panel bifold.

Sources

Prices are guide figures from the named sources, checked in November 2026, and include VAT where the source says so. They are not quotes. Always get itemised written quotes before you commit.

Similar Posts